Lexmark 60 Manual do Utilizador

Optra N Maintenance Kit

Replacing the fuser66 Pull the fuser out of the printer with both hands.Installing the new fuser1Unpack the new fuser. Remove the two orange spacers,

Replacing the fuser72 Insert the new fuser in the printer.aRest the fuser on the black rails on either side of the printer opening.bSlide the fuser al

Replacing the fuser83 Push the blue levers up to lock the fuser into place.4 If you removed the optional duplexer, reinsert it into the printer.aHold

Replacing the fuser9bPush on each end of the duplexer until it locks into place.5Close the left access door.

Replacing the fuser10

Replacing the transfer roll11Replacing the transfer rollRemoving the old transfer roll assembly1Make sure the printer power is off and the power cords

Replacing the transfer roll124 Locate the black transfer roll inside the printer. Closely observe how the transfer roll is installed.5 Carefully lift

Replacing the transfer roll13Installing the new transfer roll assembly1 Put on the rubber gloves included with the maintenance kit.The gloves protect

Replacing the transfer roll14NOTE: Improperly inserting the transfer roll assembly may damage the printer. Study the illustrations carefully before in

Replacing the transfer roll156 Align the transfer roll with the clip on the left side of the printer. 7Press the left end of the transfer roll firmly

Replacing the transfer roll1610 Reinstall the print cartridge.aLocate the grooves on either side of the printer.bSlide the cartridge into the grooves

Replacing the paper feed rollers in the printer17Replacing thepaper feed rollersin the printerRemoving the old rollersReplace all four rollers, even i

Replacing the paper feed rollers in the printer183 Locate the blue paper feed rollers in the two tray openings.The paper feed rollers are in the same

Replacing the paper feed rollers in the printer194 Pinch the release tab on the end of each roller and slide the roller off the shaft.5 Discard all fo

Replacing the paper feed rollers in the printer20Installing the new rollers1 Locate the plastic bag containing the four paper feed rollers that came i

Replacing the paper feed rollers in the printer213 Once you have replaced all four paper feed rollers, reinsert tray 1 and tray 2.aAlign the yellow la

Replacing the paper feed rollers in the printer22

Replacing the paper feed rollers in the optional input drawer23Replacing thepaper feed rollers in theoptional input drawerRemoving the old rollersRepl

Replacing the paper feed rollers in the optional input drawer243 Locate the blue paper feed rollers.4 Remove the upper roller.aUse your right hand to

Replacing the paper feed rollers in the optional input drawer255 Pinch the release tab on the end of the lower roller and slide the roller off the sha

ContentsiiiContentsIntroduction ...

Replacing the paper feed rollers in the optional input drawer263 Install the upper roller.aUse your right hand to press down lightly on the lower roll

Verifying installation27Verifying installationNOTE: To clear the Maintenance message from the printer operator panel display, and to reset the interna

Verifying installation28eSelect Single.Printing Test Page appears on the display while the page prints.If you experience a paper jam, you probably hav

Printed in U.S.A.8/96P/N 11A9972E.C. 539966© Copyright Lexmark International, Inc. 1996. All rights reserved.

Contentsiv

Introduction1IntroductionInstalling the fuser, transfer roll, and paper feed rollers included in this kit will help you avoid print quality problems a

Introduction2The following illustration shows the location of the parts you need to replace.NOTE: Before installing the items included in the maintena

Replacing the fuser3Replacing the fuserRemoving the old fuser1Make sure the printer power is off and the power cords are unplugged. NOTE: Wait 20 minu

Replacing the fuser43 If the optional duplexer is installed, remove it.aPress the green tab to unlock the duplexer. bUse both hands to pull the duplex

Replacing the fuser54 Push down firmly on the blue levers at each end of the fuser to unlock the fuser.5 Place a finger under the black tab on each en